We've carried bikes from Linus for more than six months now, and in that time we've sent a surprising number of the little guys and gals out into the world in both Chicago and Seattle. It's been a pleasure to see them locked to bike racks downtown in the Loop , rolling down the Burke Gilman, and hanging from the chain link outside bars on Capitol Hill in Seattle. I've seen them used for commuters, bar bikes, kid haulers, and “couples' cycling incentives.” Just as Linus riders seem to have discovered the versatility of the design, we've had a great time expanding the capabilities of the bikes themselves. Here are a pair of the projects Alex and I have set up with some of the bikes. We've had a huge amount of fun thinking up ways to keep the Linus style undiluted while adding function and some new ways to ride!  If you cold winter riders are  looking to set up your Linus, Chicago Schwinn or  Raleigh with a similar light set-up ask us about the Schwalbe studded tires for winter riding.  

Classic headlight, classic tire generator, classic Roadster 3, and a nice warm yellow halogen beam.

Live on the top of a monster hill? The SRAM i-Motion 9 hub nearly triples the gear range of this Dutchi.

Dream it up and your Linus can probably do it.

Just thought everyone might like to know what happens when Dutch Bike Chicago heads over to Dutch Bike Seattle. Watch until the end to see who forms the head.  Who is that guy?

Welcome back, class!  Now that you've adjusted your Shimano Nexus hubs, we'll dive into the next most interesting operation on one of these bikes: rear wheel removal.  Mastering this will allow you to replace tires or tubes that are worn out or damaged beyond patching.  This will get a little more technical than the previous post, so it's very important to make sure you're comfortable using tools and that you have the time and energy to safely put everything back together.  Please read through the entire post before tearing apart your bike, and be sure you're comfortable performing all the operations described (especially tensioning the chain!).  Troubleshooting and adjusting your hub didn't require any tools, but this will, so get out that toolkit and polish up your:

1. 15mm open-end wrench or 15mm deep socket w/ driver
2. 10mm open-end wrench and 10mm socket w/ driver (you can substitute another 10mm wrench or a small adjustable if necessary)
3. Cable cutters (diagonal cutters or wire cutters can be substituted)
4. 2mm hex key/Allen wrench
5. Dental pick, sharpened spoke, sturdy ballpoint pen, small switchblade, or something else with a nice point to it
6. Tire levers (if you plan on replacing tubes or tires)

Now that your tools are prepared, set your bike on its center stand (or clamp the seatpost in a work stand if you're lucky enough to have one).

We will remove the rear wheel first because it's a more complex operation and many of the steps will be duplicated in removing the front.  As an overview, we're going to disconnect the brake, open the chain case, disconnect the shifter, disengage the chain tensioners, and remove the wheel.  Then we will reinstall the wheel, engage the tensioners, tension the chain and center the wheel, reconnect the shifter and brake, and close the chain case.

To disconnect the brake, first loosen the cable fixing nut several turns.  Pull or clip off the cable tip, and pull the cable out of the brake.

Now once we've removed the torque arm clamp bolt the brake will be completely disconnected.

After that, move back to the right side of the bike and open the chain case, starting by unhooking the tension wire running along the bottom of the case.

Once the wire is unhooked about 3/4 of the way down toward the front, unsnap and unclip the rear section as we did in the previous post.

Now loosen the axle nuts about three turns (Don't worry, the chain tensioners will hold the wheel in place) and yank the rear section of the chain case frame straight back and out of the bike.

Shift the bike into first gear, and poke the long end of the 2mm hex key into the tiny hole in the back of the cassette joint.

Pull downward on the wrench to give yourself some cable slack, and then use your pointy tool to pop the cable and cable stop out of the cassette joint.

Pull the cable housing out of the housing stop, being careful not to kink the cable.

Now that you've disconnected the brake and shifter cables from the hub, all that's left is removing the wheel itself!  Loosen the chain tensioners until the nuts are even with the end of the threaded section, and loosen the axle nuts until the colored non-turn washers (yellow on the right, brown on the left) can completely clear the frame.

Lift the chain carefully off the teeth of the cog and set it down on the plastic of the cassette joint.

Now you'll actually remove the wheel: pull it straight backward until both chain tensioners are loose enough that you can flip them downward so that they hang from the axle.

The wheel will now be free to slide forward and out of the dropouts, and you're free to replace tubes, change tires or just marvel at your accomplishment.

To reinstall the wheel, you will essentially be reversing most of the steps you've just completed.  Set the chain on the cassette joint -- next to the cog but not on it -- and then slide the wheel back into the dropouts.  This may take some wiggling, and possibly even some fiddling to make sure that the chain tensioners are inside the dropouts, and the non-turn washers (brown and yellow) are outside.  Gently pull the wheel as far back into the dropouts as possible, giving yourself enough slack to flip the tensioners back into place.  Now that the wheel is held in place by the tensioners, you'll be able to reattach the shifter and brake cables, the chain, and the chain case.

Set the chain back on the cog and carefully turn the cranks a few revolutions to make sure that the chain is fully set on the chainwheel (front gear) as well.  To reconnect the shifter cable to the cassette joint, first slide the cable housing end into the housing stop.

Now repeat the trick with the 2mm hex key to wind the cassette joint back to a point where you can slot the cable stop into its cradle, making sure that the cable sits cleanly along its channel.   Shift up and down the range a few times to make sure that everything is working smoothly, and also use this opportunity to check the adjustment of your hub (just like you learned to do in the last post!).

Pass the brake cable through the housing stop and into the cable stop, tightening it down at at its original setting.  Make sure the housing is fully inserted in the stop.  At this point you can crimp a cable end cap onto the cable, then test brake function by pulling hard on the brake lever. 

Slide the rear section of the chain case frame into place, carefully pushing both top and bottom ends into place in the main chain case frame.  Be sure that the chain tensioner is outside the chain case frame on the axle.

Now that everything on the axle is in place, you can tension the chain.  This step is going to be the most technical that you'll perform during the operation, so shake the kinks out of your hands and get ready!  Tighten down the axle nuts until the tabs of the non-turn washers are fully inserted into the dropouts, but not so tight that you can't shift the wheel.  Throughout this step, you'll be keeping the wheel centered in the frame by watching the distance between the (ideally fully inflated) tire and the chain stays.  Tighten the chain tensioner nuts evenly as you bring the wheel back toward its original position.  On Workcycles bikes (especially if you are using the original cog size), you'll frequently be able to find this spot by the indentations left by the non-turn washers in the frame powdercoat.

Ideal chain tension can be an art and a science, but the easiest gauge will be this: at the tightest spot in the rotation of the cranks (because there will be tight spots and loose spots) you should still be able to move the chain slightly (<1/4") up and down with your fingers.  You should NOT hear a crackling sound as you spin the pedals through the tight spots, and the chain should not be so loose as to hit the bottom of the chain case.

Once you've got the chain at a nice tension, double-check the centering of the wheel and then reattach the rear brake's torque-arm clamp on the chain stay.

Now you can tighten down the axle nuts!  Make sure these are solidly tight, really get your arm behind the wrench (unless you're some sort of giant burly guy, in which case you'll want to exercise some restraint).

Now that the wheel is reinstalled and the chain case frame is reassembled, most of what's left should be familiar from the last post: closing the chain case.  Gently (because these are fabric parts, after all...) slide the rear section of the cover over the frame, keeping the chain tensioner outside.  Pull the edges of the inside slit (between the wheel and the chain case) together and slide the prongs of the clip into their pockets inside the chain case.  Snap the snap on the outside, and hook the wire back and forth across the hooks on the underside (don't miss any!).

...And you're done.  Go for a ride!

As you may have guessed, we love some internally geared hubs here at Dutch Bike Co.  We love the smooth shifting, the quiet operation, and the simplicity of use.  From the shop perspective, I enjoy knowing that our bikes are out there being ridden and loved - not worked on.
 
More than any other drivetrain, an 8 speed hub really doesn't require its user to be a "bike person."  An avid cyclist will certainly enjoy it -- as many of you have discovered for yourselves -- but anyone who can push the pedals will benefit equally from the utter simplicity and rock-like durability of this transmission.  Combine the system with a chaincase and in a year of riding you'll probably do no maintenance whatsoever.  You won't even have to wonder whether or not to feel guilty about it.

This brings us to the educational kernel nestled within this husk of a post: adjusting your Shimano Nexus hub.  At this point, you might reasonably grow apprehensive that I'll try to explain planetary gear systems, expose you to exploded views, or start talking about gear inches.  I won't.  Adjusting your hub is a simple and easy procedure that will likely take less than five minutes and won't get your hands very greasy at all.

Step One: Diagnosis
When I teach a repair class, this is typically the subject that receives the strongest emphasis.  Without understanding what's causing the problem, we can't fix it.  Bearing this firmly in mind, we'll quickly check the three main parts of the system: the shifter, the cable, and the cassette joint (I'll explain in a moment).  The cable will come first, because it's the simplest part of the system and -- relatively speaking -- the most vulnerable.  Around three out of four "mis-shifting" or "gear slipping" issues on our bikes have the same simple cause:



Here, the cable housing (the outer sheath) has been tugged out of the shifter, exposing the cable.  It has then caught on the edge of its proper place (the barrel adjuster) and failed to snap back in.  This 1/4" difference leaves the system totally out of whack.  The solution is even simpler than the problem: just nudge the end of the housing back into the barrel adjuster, and the tension already on the cable will do the rest, snapping it back into place.



If all is well so far, check over as much of the shifter cable housing as you can see for damage or kinks that could cause it to drag or bind.

Next, we'll move on to the cassette joint.  This is the little plastic unit on the side of the hub where the cable attaches, and that translates your pull on the cable into the actual gear change in the hub.  If you have a cloth chaincase (any Workcycle, Azor, or Jorg&Olif except Secret Service, Fr8, and Bakfiets) you'll need to open the back end just a little to see the cassette joint.  Unsnap the outside snap, then slide the clip out of the pockets on the inside.



Gently peel the rear section of the chaincase up and forward, and tuck it out of the way.



Now you'll be able to see the gray and black plastic cassette joint, and the little adjustment window with a yellow indicator line.  With a plastic chaincase you'll just be able to flex it inward slightly, and the view will be the same.



Now that you've ruled out problems with the cable, shift into fourth gear (you'll see a dot next to the number to tell you it's special) and check the yellow marks in the small window on the top of the cassette joint: if they line up, you're adjusted properly.  If they don't, then turn the adjuster on the shifter (with a couple of experimental turns to make sure of your direction) until they do.



...And you're done!  You've just done exactly what a good mechanic would have when confronted with Nexus hub "issues," and almost assuredly resolved them.  Take the bike for a quick test ride, and enjoy your perfect shifting.